New construction
Pipe and inlets go in before drywall. Rough-in details.
Installation
Central vacuum installation
New-home installation and central vacuum installation in existing homes across Simcoe County. Installation is quoted for your home after a free visit.
New homes
New-home installation
We help you choose suitable equipment, plan piping and inlet locations, and place the power unit for quiet, practical use.
- Inlet layout for living areas and bedrooms
- Power-unit placement away from main living spaces
- Hose reach and cleaning coverage considered in the plan
- System checks and operating instructions after installation
What an installation quote includes
Your free in-home quote covers the selected equipment, labour, materials and any stated exclusions. It also addresses inlet locations, hose reach, power-unit placement and compatibility with existing piping where relevant.
Electrical work, if needed, must be done by a licensed electrician and is not included in our quote.
Request a Free QuoteExisting homes
Adding a Central Vacuum to an Existing Home
We assess accessible routes through basements, closets, garages and attic spaces to plan your installation. If wall openings or other access work are needed, we explain the requirements before work begins.
- Assessment of accessible piping routes
- Clear discussion of access points before work begins
- Power-unit upgrades on existing piping where compatible
Process
How installation works
01
Initial discussion
Tell us about your home, flooring and goals.
02
Assessment where needed
We review layout and access routes, especially for existing homes.
03
Written quote
Equipment, labour, materials and exclusions in writing.
04
Scheduling and installation
We schedule the work, install the system, run checks and explain operation.
Planning
What goes into a good installation
Finished-home retrofits
Routes through basements, closets and attics. Retrofit details.
Unfinished basements
Make main-floor runs fast and tidy, with pipe along the joists.
Inlet placement
Central spots near stairs and halls so one hose reaches several rooms. How many inlets?
Pipe routing
Smooth sweep fittings and the shortest practical runs keep airflow strong and reduce clogs.
Power-unit placement
Garage, basement or utility room. Power-unit installation.
Garage inlets
Useful for cars and workshops. Easiest to add when the unit is in or near the garage.
Exterior exhaust
Sends fine dust and warm air outside. Exhaust venting.
Low-voltage wiring
A thin wire runs with the pipe to each inlet so the unit starts when you plug in the hose.
120 V vs 240 V
Most homes use 120 V. 240 V dual-motor units suit very large systems and need a 240 V supply by a licensed electrician (not included).
Existing pipe reuse
Old pipe in good condition can usually stay. We test it first. Replacement units.
Pricing
What affects central vacuum installation cost?
Installation pricing depends on the actual home and scope, so we quote it after a free visit rather than posting a flat price. Equipment prices are listed on our Systems page. HST is extra.
Home size and layout
Bigger homes need longer pipe runs and often more inlets.
Number of inlets
Each inlet adds pipe, fittings, a valve and labour.
New build vs finished home
Open walls are faster. Finished homes take route-finding and care.
Accessibility
Unfinished basements and attic access make work quicker than finished ceilings.
Pipe runs
The number and length of runs, and how many floors they climb.
Garage inlet
Optional, often simple from a basement or garage-mounted unit.
Exterior exhaust
Optional vent pipe and wall cap to send exhaust outside.
Existing pipe
Reusable pipe can lower the cost. We test it first.
Power unit
Model choice, and whether a 240 V supply is needed (electrical by a licensed electrician, not included).
New builds
Roughing in a new home
The best time to plan a central vacuum is before the drywall goes up. During rough-in we run piping through the open walls and floors, set inlet valves where they make sense for your rooms, and plan a pipe route to where the power unit will sit.
Once the home is near completion, we come back to install the power unit, connect the low-voltage wiring, fit the inlet covers and test the system. If you are working with a builder in Barrie, Innisfil or Bradford, we are happy to coordinate timing with them.
Installation day
What to expect on the day
01
Arrival and layout
We confirm inlet locations and the pipe route with you before drilling anything.
02
Piping and inlets
Pipe runs through basements, closets and attic spaces, with inlets placed for good hose reach.
03
Power unit
The power unit is mounted and connected. Electrical work, if needed, is done separately by a licensed electrician.
04
Testing and walkthrough
We test suction at every inlet, clean up, and show you how to empty the unit and look after the filter.
Planning tips
Getting the most from your system
Hose reach matters more than the number of inlets. A well-placed inlet with a 30 or 35 foot hose can cover a lot of floor, so we plan around how you actually move through your home.
Think about your floors. Mostly hard floors work well with a bare-floor package, while carpet benefits from an electric powerhead. Our Products page lists the Beam and CycloVac options with equipment prices in Canadian dollars.
Service area
Serving Barrie, Innisfil and communities across Simcoe County
We install central vacuums in new and existing homes in Barrie, Innisfil (including Alcona, Lefroy, Stroud and Cookstown), Bradford, Angus and nearby Simcoe County communities. Your in-home installation quote is free.
If you live nearby and are not sure whether you are in our area, call (416) 856-6245 or email info@simcoevac.com and we will let you know.
Towns we visit
- Barrie
- Innisfil
- Alcona
- Bradford
- Lefroy
- Stroud
- Cookstown
- Angus
Serving Simcoe County since 2016.
FAQ
Installation questions
How much does central vacuum installation cost in an existing home?
It depends on the size of the home, how many inlets you want and how easy it is to run pipe. We quote it for free in your home and give you a written price before any work is booked. HST is extra.
When should a new build be roughed in?
After framing and before insulation and drywall. That is when pipe and inlet valves can go in cleanly. The power unit and finished inlets are installed later, once the home is close to move-in.
How long does installation take?
It depends on the home. A rough-in or a straightforward existing-home installation can usually be done in a day, while larger homes or tricky access can take longer. We give you a time estimate with your quote.
Will there be holes in my walls?
We try to route pipe through basements, closets, the garage and the attic to keep wall openings to a minimum. If an opening is needed, we show you where and explain it before we start.
Where does the power unit go?
Usually in the basement, garage or a utility room, away from living spaces so you hear very little while vacuuming. We pick a spot with room to empty the unit and service the filter.
Is electrical work included?
No. If your home needs a new dedicated circuit or outlet for the power unit, that work must be done by a licensed electrician and is not included in our price. This applies to 120 V and 240 V units. We will tell you what the power unit needs so your electrician can plan for it.